acceptanceCriteriaName
Provides the name of the acceptance criteria template policy used to compare the measured results
tmnxOamSathStsSvcStrmAcpCritTmpl
cirRate
The user-configured CIR rate
tmnxOamSathStsSvcStrmTxCIR
cTagDot1p
The dot1p value set for VLAN tag 2 (inner VLAN tag) in the frame payload generated by the tool
tmnxOamSathStsSvcStrmCustTagPrio
cTagDei
The DEI value set for VLAN tag 2 (inner VLAN tag) in the frame payload generated by the tool
tmnxOamSathStsSvcStrmCustTagDEI
cirTestDurMin
The duration, in minutes, of the CIR test
tmnxOamSathStsSvcTestDrCirMin
cirTestDurSec
The duration, in seconds, of the CIR test
tmnxOamSathStsSvcTestDrCirSec
cirThreshold
The CIR rate threshold to compare with the measured value
tmnxOamSathStsSvcStrmAcThldCir
dataPattern
The data pattern to include in the packet generated by the service testhead tool
tmnxOamSathStsSvcStrmPadPattern
description
The user-configured description for the service test and service stream
tmnxOamSathStsSvcTestDescription
tmnxOamSathStsSvcStrmDescription
dstMac
The destination MAC address to use in the packet generated by the tool
tmnxOamSathStsSvcStrmDestMacAddr
delayVarMax
The maximum value of delay variation measured by the tool
tmnxOamSathStsTestMeasDelayVrMax
delayVarMin
The minimum value of delay variation measured by the tool
tmnxOamSathStsTestMeasDelayVrMin
delayVarAvg
The average value of delay variation measured by the tool
tmnxOamSathStsTestMeasDelayVrAvg
delayVariationAcceptancePass
Indicates whether the measured delay variation is within the configured delay variation threshold in the acceptance criteria
tmnxOamSathStsTestOprStDelayVar
delayVariationThreshold
The delay variation threshold configured in the acceptance criteria
tmnxOamSathStsSvcStrmAcThldDlyVr
delayAcceptancePass
Indicates whether the measured delay is within configured delay threshold
tmnxOamSathStsTestOprStDelay
delayAvg
The average of delay values computed for the test stream
tmnxOamSathStsTestMeasDelayAvg ncy
delayMax
The maximum value of delay measured by the tool
tmnxOamSathStsTestMeasDelayMax
delayMin
The minimum value of delay measured by the tool
tmnxOamSathStsTestMeasDelayMin
delayThreshold
The delay threshold configured in the acceptance criteria
tmnxOamSathStsSvcTestTimeEnd
endTime
The time (wall-clock time) the test was completed
tmnxOamSathStsSvcTestTimeEnd
tmnxOamSathStsTestTimeEnd
frameLossThreshold
The loss threshold configured in the acceptance criteria
tmnxOamSathStsSvcStrmAcThldFLR
frameLossThresholdPolicing
The loss threshold configured in the acceptance criteria for the policing test
tmnxOamSathStsSvcStrmAcThldFlrPl
frameSizeTemplateName
The frame size template name. The testhead tool generates packet sizes as specified in the frame size template. This is used to specify a mix of frames with different sizes to be generated by the tool.
tmnxOamSathStsSvcStrmFrmSizeTmpl
lossRatio
The measured frame loss ratio
tmnxOamSathStsTestMeasFLR
lossAcceptancePass
Indicates whether the measured loss ratio is within the configured loss threshold
tmnxOamSathStsTestOprStFLR
measuredThroughput
The measured throughput
tmnxOamSathStsTestMeasThroughput
mepId
The configured source MEP
tmnxOamSathStsSvcStrmSrcMepId
mepDomain
The configured Maintenance Domain (MD) for the MEP
tmnxOamSathStsSvcStrmSrcMdIndex
mepAssociation
The configured Maintenance Association (MA) for the MEP
tmnxOamSathStsSvcStrmSrcMaIndex
mfactor
A factor to use as a margin by which the observed throughput is off from the configured throughput to determine whether a service test passes or fails
tmnxOamSathStsSvcStrmAcMFactor
perfTestDurHours
The duration, in hours, of the performance test
tmnxOamSathStsTestDrPerfHours
perfTestDurMin
The duration, in minutes, of the performance test
tmnxOamSathStsSvcTestDrPerfMin
perfTestDurSec
The duration, in seconds, of the performance test
tmnxOamSathStsTestDrPerfSec
pirRate
The PIR rate configured
tmnxOamSathStsSvcStrmTxPIR
pirTestDurMin
The PIR test duration, in minutes
tmnxOamSathStsSvcTestDrCirPirMin
pirTestDurSec
The PIR test duration, in seconds
tmnxOamSathStsSvcTestDrCirPirSec
pirThreshold
The PIR threshold configured in the acceptance criteria
tmnxOamSathStsSvcStrmAcThldPIR
pktCountRx
The received packet count
tmnxOamSathStsTestMeasFramesRx
pktCountTx
The transmitted packet count
tmnxOamSathStsTestMeasFramesTx
policeTestDurMin
The policing test duration, in minutes
tmnxOamSathStsSvcTestDrPoliceMin
policeTestDurSec
The policing test duration, in seconds
tmnxOamSathStsSvcTestDrPoliceSec
port
The source port used as the test launch point
tmnxOamSathStsSvcStrmSrcRtrPort
routerInstance
The routing instance of the interface launching the test
tmnxOamSathStsSvcStrmSrcRtrInst
routerInterface
The configured router interface launching the test
tmnxOamSathStsSvcStrmSrcRtrIf
runNumber
The run number of the test
tmnxOamSathStsSvcTestRun
runOperState
The operational status of the service test and service stream.
tmnxOamSathStsSvcTestOprState
tmnxOamSathStsSvcStrmOprState
tmnxOamSathStsTestOprState
sap
The SAP used as the test endpoint
tmnxOamSathStsSvcStrmSrcSAP
sequence
The sequence of payload sizes specified in the frame-mix policy
tmnxOamSathStsSvcStrmFrmSizeSeq
sizeA
The user can configure a frame sequence to indicate the sequence of frame sizes to be generated by the tool. The frame sequence is specified using letters ‟a” to ‟h” and ‟u”. sizeA specifies the frame size for the packet identified with the letter ‟a” in the frame sequence.
tmnxOamSathStsSvcStrmFrmSizeA
sizeB
The user can configure a frame sequence to indicate the sequence of frame sizes to be generated by the tool. The frame sequence is specified using letters ‟a” to ‟h” and ‟u”. sizeB specifies the frame size for the packet identified with the letter ‟b” in the frame sequence.
tmnxOamSathStsSvcStrmFrmSizeB
sizeC
The user can configure a frame sequence to indicate the sequence of frame sizes to be generated by the tool. The frame sequence is specified using letters ‟a” to ‟h” and ‟u”. sizeC specifies the frame size for the packet identified with the letter ‟c” in the frame sequence.
tmnxOamSathStsSvcStrmFrmSizeC
sizeD
The user can configure a frame sequence to indicate the sequence of frame sizes to be generated by the tool. The frame sequence is specified using letters ‟a” to ‟h” and ‟u”. sizeD specifies the frame size for the packet identified with the letter ‟d” in the frame sequence.
tmnxOamSathStsSvcStrmFrmSizeD
sizeE
The user can configure a frame sequence to indicate the sequence of frame sizes to be generated by the tool. The frame sequence is specified using letters ‟a” to ‟h” and ‟u”. sizeE specifies the frame size for the packet identified with the letter ‟e” in the frame sequence.
tmnxOamSathStsSvcStrmFrmSizeE
sizeF
The user can configure a frame sequence to indicate the sequence of frame sizes to be generated by the tool. The frame sequence is specified using letters ‟a” to ‟h” and ‟u”. sizeF specifies the frame-size for packet identified with letter ‟f” in the frame-sequence.
tmnxOamSathStsSvcStrmFrmSizeF
sizeG
The user can configure a frame sequence to indicate the sequence of frame sizes to be generated by the tool. The frame sequence is specified using letters ‟a” to ‟h” and ‟u”. sizeG specifies the frame size for the packet identified with the letter ‟g” in the frame sequence.
tmnxOamSathStsSvcStrmFrmSizeG
sizeH
The user can configure a frame sequence to indicate the sequence of frame sizes to be generated by the tool. The frame sequence is specified using letters ‟a” to ‟h” and ‟u”. sizeH specifies the frame size for the packet identified with the letter ‟h” in the frame sequence.
tmnxOamSathStsSvcStrmFrmSizeH
sizeU
The user can configure a frame sequence to indicate the sequence of frame sizes to be generated by the tool. The frame sequence is specified using letters ‟a” to ‟h” and ‟u”. sizeU specifies the frame size for the packet identified with the letter ‟u” in the frame sequence. sizeU is the user-defined packet size.
tmnxOamSathStsSvcStrmFrmSizeU
srcMac
The source MAC address in the frame payload generated by the tool
tmnxOamSathStsSvcStrmSrcMacAddr
sTagDot1p
The dot1p value set for VLAN tag 1 (outermost VLAN tag) in the frame payload generated by the tool
tmnxOamSathStsSvcStrmSvcTagPrio
sTagDei
The DEI value set for VLAN tag 1 (outermost VLAN tag) in the frame payload generated by the tool
tmnxOamSathStsSvcStrmSvcTagDEI
startTime
The time at which the test was started (wall clock time)
tmnxOamSathStsSvcTestTimeStart
streamId
The stream identifier
tmnxOamSathCfgSvcStrmNum
streamRunOrder
Indicates if the streams configured for the service test were run one after another or run in parallel. This is for each stream and test type.
tmnxOamSathSvcTestStrRunOrder
testCir
The CIR configuration test
tmnxOamSathStsSvcStrmCIR
testCirPir
The CIR-PIR configuration test
tmnxOamSathStsStrmCirPir
testPerf
The performance test
tmnxOamSathStsSvcStrmPerformance
testPolicing
The policing test
tmnxOamSathStsSvcStrmPolicing
testname
The service test name
tmnxOamSathCfgSvcTestName
throughputAcceptancePass
Indicates whether the measured throughput matches the configured CIR/PIR rate
tmnxOamSathStsTestOprStThroughpt
trapNotification
Indicates whether the trap must be sent after completion of the test
tmnxOamSathStsSvcTestComplNotif
tmnxOamSathStsSvcStrmComplNotif
